MATERIAL SAFETY DATA SHEET Section I. Identity Product Name: AMALFI CA Manufacturer: AMALFI INGREDIENTS Manufacturer’s Address: 94 E. Jefryn Blvd,Unit H, Deer Park, NY 11729 Manufacturer’s Phone #: 631-392-1526 Chemtrec Phone #: 800-424-9300 Date Prepared: JUNE 2006 Section II. Hazardous Ingredients/Identity Information Hazardous Components (Specific Chemical Identity: Common Name (s)) Other limits recommended % OSHA PEL ACGIH Threshold Limit Value (units) Components: Propylene Glycol CAS # 57-55-6 Citric Acid CAS # 77-92-9 Section III. Physical/Chemical Characteristics Boiling Point: N/A Vapor Pressure (mm Hg.): < 1 mm Hg @ 68o F Vapor Density (AIR=1): N/A Solubility in Water: PG = Miscible, CA = 64.3% Specific Gravity (H2O=1): > 1.0 @ 20/4o C Melting Point: N/A Evaporation Rate (Butil Acetate=1): N/A Appearance & Odor: Amber liquid, practically odorless. Section IV. Fire & Explosion Hazard Data Flash Point: > 200o F (> 93o C) pmcc Flammable Limits: N/A Extinguishing Media: Water fog, dry chemical, CO2, foam LEL: N/A UEL: N/A Special Fire Fighting Procedures: Wear self contained breathing apparatus and protective clothing Unusual Fire & Explosion Hazards: Toxic vapors may be given off in a fire. In a finely divided form, such as a mist, spray or aerosol, product can be ignited at temperatures below its flash point and may represent an explosion hazard. Section V. Health Hazard Data OSHA Regulate: No Carcinogen – NTP Program: No Carcinogen – IARC Program: No Health Hazards (Acute Chronic): May irritate the eye, skin, and respiratory tract. Signs & Symptoms of Exposure: Medical Conditions Aggravated by Exposure: Routes of Entry: Inhalation - possible, skin - yes, ingestion - possible. Emergency First Aid: Inhalation: Remove affected person to fresh air. Eyes: Flush with water for at least 15 minutes. Obtain immediate medical attention. Skin: Wash affected area with soap and water. Ingestion: Obtain immediate medical attention and consult with physician about inducing vomiting. Never give anything by mouth if the affected person is losing consciousness, is unconscious or is convulsing. Section VI. Reactivity Data Stability: Stable Conditions to Avoid: Oxidizing agents. Exposure to heat and light. Incompatibility (Materials to Avoid): Strong oxidizing agents Hazardous Decomposition or Byproducts: CO, CO2, acetic acid propionaldehyde Hazardous Polymerization: Will not occur Section VII. Precautions for Safe Handling and Use: Steps to Be Taken in Case Materials are Released or Spilled: Sweep or vacuum spilled material into appropriate container. For large spills confine entry into the affected area to those persons properly protected. Remove all sources of ignition. Spill should be contained through the use of commercial oil adsorbent, but other materials such as earth, sand, or sawdust may be more expedient to limit the extent of the spill. Sweep, shovel or vacuum spilled material into appropriate container. Waste Disposal Method: Product should be disposed in accordance with all applicable national, state, or local laws. Precautions to Be Taken in Handling and Storing: Store in tightly closed, properly labeled containers in cool (< 100° F, <38°C), well ventilated area away from all ignition sources. Avoid contact with skin and eyes. Avoid inhalation of product vapors or mist. Do not take internally. Other Precautions: Section VIII. Control Measures Eye Protection: Safety glasses or goggles Local Exhaust: Respiratory Protection: Use an organic vapor respirator (NIOSH/MSHA approved) if mist or vapor inhalation may occur Other Protective Clothing or Equipment: Work uniform as necessary to prevent repeated or prolonged skin contact. Protective Gloves: Recommended Ventilation: Recommended Work/Hygienic Practices: DISCLAIMER: The information in this MSDS was obtained from current and reliable sources. However , the data is provided without any warranty , expressed or implied, regarding its correctness or accuracy. Since the conditions of handling, storage and disposal of this product are beyond our control, it is the responsibility of the user both to determine safe conditions for use of this product and to assume full responsibility for loss, injury and expense arising out of product’s improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage use or disposal of this product which may not be covered in this MSDS. The user is responsible for full compliance. |