MATERIAL SAFETY DATA SHEET Section I. Identity Product Name: AMALFI 8 Manufacturer: AMALFI INGREDIENTS Manufacturer’s Address: 94 E. Jefryn Blvd,Unit H, Deer Park, NY 11729 Manufacturer’s Phone #: 631-392-1526 Chemtrec Phone #: 800-424-9300 Date Prepared: JUNE 2006 Section II. Hazardous Ingredients/Identity Information Hazardous Components (Specific Chemical Identity: Common Name (s)) Other limits recommended % OSHA PEL ACGIH Threshold Limit Value (units) Components: Vegetable Oil 2,6-di-tert-butylpara-cresol (BHT) CAS # 128-37-0 Section III. Physical/Chemical Characteristics Boiling Point: N/A Vapor Pressure (mm Hg.): <1 mm Vapor Density (AIR=1): N/A Solubility in Water: Insoluble Specific Gravity (H2O=1): ~ 0.925 g Melting Point: < -70oF (< 57oC) Evaporation Rate (Butil Acetate=1): N/A Appearance & Odor: Practically Odorless Pale Amber Liquid Section IV. Fire & Explosion Hazard Data Flash Point: 490o F (254o C) Flammable Limits: N/A Extinguishing Media: Water Fog; CO2, Dry chemical, Foam LEL: N/A UEL: N/A Special Fire Fighting Procedures: Wear protective clothing and self contained breathing apparatus Unusual Fire & Explosion Hazards: CO, CO2, NOx vapors may be given off in a fire Section V. Health Hazard Data OSHA Regulate: None Classified Carcinogen – NTP Program: None Carcinogen – IARC Program: None Health Hazards (Acute Chronic): BHT is a severe eye irritant. The other components are not known to cause eye irritation. Blurred vision may occur upon contact due to physical presence of oil on the eye. Signs & Symptoms of Exposure: Medical Conditions Aggravated by Exposure: Allergic sensitivities (MCS), Psoriases, Acne, Eczema Routes of Entry: Inhalation - unlikely, skin - possible, ingestion - yes Emergency First Aid: Wash affected area with soap and water. Flush eyes with water for a minimum of 15 minutes. Obtain prompt professional medical attention. Section VI. Reactivity Data Stability: Stable Conditions to Avoid: Oxidizing Agents Incompatibility (Materials to Avoid): Copper & Copper Alloys Hazardous Decomposition or Byproducts: Hazardous Polymerization: Will not occur Section VII. Precautions for Safe Handling and Use: Steps to Be Taken in Case Materials are Released or Spilled: Sweep or vacuum spilled material into an appropriate container. Use absorbent material (vermiculite, kitty littler, sand, etc.). Waste Disposal Method: In accordance with all applicable regulations (State and Local). Precautions to Be Taken in Handling and Storing: Away from high heat and all ignition sources. Other Precautions: Store in cool, well ventilated area <100°F, away from sunlight Section VIII. Control Measures Eye Protection: Recommended Local Exhaust: Respiratory Protection: Mask or respirator if mist or vapor occur Other Protective Clothing or Equipment: Work uniform. Protective Gloves: Recommended Ventilation: Recommended Work/Hygienic Practices: Wash after handling DISCLAIMER: The information in this MSDS was obtained from current and reliable sources. However , the data is provided without any warranty , expressed or implied, regarding its correctness or accuracy. Since the conditions of handling, storage and disposal of this product are beyond our control, it is the responsibility of the user both to determine safe conditions for use of this product and to assume full responsibility for loss, injury and expense arising out of product’s improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage use or disposal of this product which may not be covered in this MSDS. The user is responsible for full compliance. |